Identifying which mechanism is fitted before ordering a spare avoids a wasted trip, since a flush valve will not fit where a siphon body was designed to sit and vice versa. Lifting the cistern lid and looking for a vertical tube with a bell-shaped top, rather than a flat valve seated directly over the outlet, is usually enough to tell the two apart on site. Plumb2U stocks siphon replacement units and modern flush valves side by side, at trade prices, for plumbers working across the full range of cistern ages found on a typical UK round. With next-day despatch on the common lines, Plumb2U's range covers the older gravity-fed jobs as readily as the newer dual-flush cisterns.
Top-fix hinges solve exactly that access problem by using a bolt and a quick-release or turn-to-tighten fixing that can be adjusted entirely from above the pan, with no need to get underneath at all. This has made top-fix the standard choice on most new soft-close seats sold in the last several years, and it is usually the easier option to specify when the underside of the pan is difficult to reach or when the original fixing has seized.
A dual-flush button looks simple from the top of the cistern lid, but underneath it is doing a more complicated job than a single-flush handle ever had to. Pressing one half of the button needs to trigger a short flush, while the other half needs to lift the flush valve fully for a complete cycle, and the mechanism that makes this happen is usually either a rigid spindle or a flexible cable running down to the flush valve itself.
The flush valve tells a different story. If water is draining slowly from the cistern into the pan even when nobody has touched the button or handle, https://quiteamazing.directory/directory/plumb2u/ the flush valve seal or siphon washer has likely perished and is no longer sealing the outlet at the base of the tank. This shows up as a cistern that refills every few minutes with no obvious trigger, sometimes described by customers as topping itself up rather than running continuously. On older gravity-fed systems built around a siphon rather than a valve, a split diaphragm inside the siphon body produces the same symptom.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, whereas a valve can simply be held open for a shorter or longer period.
Plumb2U stocks side levers, lid-mounted levers and the link arms and clips that connect them to flush valves and siphons, priced for trade buyers ordering more than one at a time. For a plumber working through several lever jobs a week, having a trade supplies merchant that lists the fitting details clearly rather than a single generic photo makes the difference between one van visit and two. Plumb2U, trading from Epsom but supplying trade accounts UK-wide, carries a lever range that covers most of what turns up on a round.
Top-fix hinges solve exactly that access problem by using a bolt and a quick-release or turn-to-tighten fixing that can be adjusted entirely from above the pan, with no need to get underneath at all. This has made top-fix the standard choice on most new soft-close seats sold in the last several years, and it is usually the easier option to specify when the underside of the pan is difficult to reach or when the original fixing has seized.
A dual-flush button looks simple from the top of the cistern lid, but underneath it is doing a more complicated job than a single-flush handle ever had to. Pressing one half of the button needs to trigger a short flush, while the other half needs to lift the flush valve fully for a complete cycle, and the mechanism that makes this happen is usually either a rigid spindle or a flexible cable running down to the flush valve itself.
The flush valve tells a different story. If water is draining slowly from the cistern into the pan even when nobody has touched the button or handle, https://quiteamazing.directory/directory/plumb2u/ the flush valve seal or siphon washer has likely perished and is no longer sealing the outlet at the base of the tank. This shows up as a cistern that refills every few minutes with no obvious trigger, sometimes described by customers as topping itself up rather than running continuously. On older gravity-fed systems built around a siphon rather than a valve, a split diaphragm inside the siphon body produces the same symptom.
A flush valve, by contrast, works as a straightforward seal at the base of the cistern that lifts to let water fall directly through into the pan under gravity, with no siphoning action involved, and shuts again once the float or timer mechanism allows it to reseat. Flush valves are what almost all dual-flush cisterns use, since a siphon's all-or-nothing action makes a genuine short flush difficult to achieve, whereas a valve can simply be held open for a shorter or longer period.
Plumb2U stocks side levers, lid-mounted levers and the link arms and clips that connect them to flush valves and siphons, priced for trade buyers ordering more than one at a time. For a plumber working through several lever jobs a week, having a trade supplies merchant that lists the fitting details clearly rather than a single generic photo makes the difference between one van visit and two. Plumb2U, trading from Epsom but supplying trade accounts UK-wide, carries a lever range that covers most of what turns up on a round.